Head Spa TL-A10-800 Control Panel | 800W

The Head Spa TL-A10-800 control panel is an electronic spare part intended to replace a control module used on a compatible water circulation system.

Its technical label bears the designation Water Circulation Wellness Machine and specifies in particular an output power of 800 W, an input voltage AC 110 V / 220–240 V and a pump specification of 12 V – 25 W.

This box can be used to replace a defective original module when its part number, wiring, connectors and electrical characteristics match those of installation.

An electronic box for the Head Spa water circulation system

Head Spa equipment uses different electrical components to ensure the operation of their water circulation systems and associated controls.

The TL-A10-800 box constitutes an element of this system. Its exact functions depend on the electrical architecture of the device on which it is installed.

Its replacement therefore requires checking the compatibility of all the connections and equipment controlled by the module.

Reference TL-A10-800: the first compatibility criterion

The reference TL-A10-800 is the main information allowing this control box to be identified.

It must be compared to the reference listed on the module currently installed on your Head Spa equipment.

Two visually similar modules may have differences in connectors, electrical pinouts or functions. The external resemblance is therefore not enough to guarantee their compatibility.

Attention: the reference TL-A10-800 is different from the reference TL-B10-800. Their interchangeability must be confirmed by the manufacturer before any replacement.

Output power: 800 W

The box has an indication Output Power: 800 W.

This value corresponds to the output power announced on the technical label of the module.

It should not be confused with the total power consumption of the Head Spa nor with the power of a particular component, such as than a water heater, without confirmation of the electrical documentation.

Before any installation, a professional must verify that this characteristic corresponds to the requirements of the original module and associated circuits.

Input voltage: AC 110 V / 220–240 V

The label indicates an input voltage AC 110 V / 220–240 V.

This information allows you to identify the voltages mentioned by the manufacturer for the TL-A10-800 model.

The actual configuration of the box delivered must nevertheless be checked before connection. The presence of several values on a label does not, in itself, allow us to conclude that all versions operate automatically on each indicated voltage.

Verification by a qualified professional is essential for any installation connected to the building's power supply.

Indicated frequency: 50–60 Hz

The TL-A10-800 panel carries a frequency indication de 50–60 Hz.

This value appears on the label under the heading “Output Frequency” and must be interpreted within the framework of the manufacturer's electrical characteristics.

It constitutes additional data to be compared with the indications on the original box.

Pump specification: 12 V – 25 W

The nameplate reads Pump Specification: 12 V – 25 W.

This value must be checked against the pump and electrical circuit provided on your Head Spa equipment.

Pumps used on different models can operate with different voltages and powers.

A pump requiring 24 V or having other characteristics must not be connected to this module without explicit technical confirmation.

Protection index IPX4

The TL-A10-800 case bears the marking IPX4.

This index corresponds to protection against splashes of water coming from different directions, under the conditions provided for by the classification.

It does not mean that the case is waterproof against immersion or that it can be directly and permanently exposed to water.

The installation must respect the location and protection conditions defined by the manufacturer, particularly in a Head Spa environment where humidity is present.

CE marking and normative reference

The module label has a CE marking and mentions the normative reference EN IEC 55014-1:2021.

This standard concerns the electromagnetic emissions requirements for certain categories of devices and equipment.

These inscriptions make it possible to identify the references declared on the product. They do not replace the applicable conformity documents or the checks necessary for the integration of the box into a professional installation.

Why replace a Head Spa control panel?

Several malfunctions can lead to the electronic system of Head Spa equipment having to be examined:

• Lack of reaction from the control system.
• Electronic module which no longer appears to be powered.
• Electrical function no longer responding correctly.
• Irregular operation of the controls.
• Controlled component which no longer starts.
• Electronic fault diagnosed by a professional.

These symptoms do not automatically mean that the box is defective. A fault can also come from a cable, a connector, a power supply, a pump or another electrical element.

Prior diagnosis helps avoid unnecessary replacement of a functional part.

A spare part for compatible Head Spa equipment

The TL-A10-800 can be intended for equipment from different manufacturers when the reference and electrical characteristics correspond.

Compatibility depends on the version of the housing, connections, connectors and electrical elements of the installation.

It is therefore recommended to photograph the label and connections of the original module before ordering.

Japan Head Spa: electronic spare parts and control panels

Japan Head Spa offers a selection of components intended for maintenance and maintenance of professional hair care equipment.

Discover our catalog of Head Spa control panels and replacement electronic boxes to identify the references suitable for your installation.

Product type	Head Spa control box / panel
Manufacturer designation	Water Circulation Wellness Machine
Exact reference	TL-A10-800
Output power	800W
Input voltage	AC 110 V / 220–240 V
Indicated current type	Alternating current (AC)
Indicated frequency	50–60 Hz (Output Frequency)
Pump specification	12 V – 25 W
Protection rating indicated	IPX4
Marking present	CE
Standard mentioned	EN IEC 55014-1:2021
Main function	Electronic control module for water circulation system
Equipment concerned	Head Spa with compatible electrical configuration
Electrical connectors	Compare with the original module
Pinching	Compatibility to be confirmed before installation
Compatibility with TL-B10-800	Interchangeability not confirmed
Universal compatibility	No
Installation	By a qualified electrical professional
Price including tax	349,00 €

1. Identify the reference of your current case

Locate the nameplate of your original module and check that it corresponds to the reference TL-A10-800.

A similar reference does not constitute proof of compatibility. Manufacturing variants must also be taken into account.

2. Check the electrical voltages

Compare the input voltage of your old module with the AC 110 V / 220–240 V indications on the TL-A10-800.

A qualified professional must confirm the configuration of the case and the compatibility with the electrical network of the installation.

3. Compare Power Output

The new module is marked 800 W. Check the power required by your system before any replacement.

4. Check pump specifications

The nameplate indicates a pump specification of 12 V – 25 W. The specifications of the pump connected to the corresponding circuit should be checked.

Do not assume compatibility with a pump operating at a different voltage.

5. Examine connectors and pinouts

Compare the number, shape and arrangement of connectors, as well as their electrical pinouts.

Two boxes of the same power may have incompatible connections.

Never modify the wiring to adapt a module whose electrical compatibility has not been confirmed.

6. Do not confuse TL-A10-800 and TL-B10-800

These two designations correspond to different references. The presence of common characteristics, such as an announced power of 800 W, does not guarantee their interchangeability.

Before using one of these references in place of the other, technical confirmation from the manufacturer is necessary.

Precisely identify the fault

A lack of reaction from the control panel does not systematically mean that the box is out of service.

The malfunction may also be linked to the power supply, a damaged cable, electrical protection, a connector or an associated component.

It is recommended to have the problem diagnosed before replacing the electronic module.

Installation by a qualified professional

The TL-A10-800 is electronic equipment capable of being connected to the mains supply.

Its replacement must be entrusted to a qualified electrical professional.

Before any intervention, the installation must be powered off and secured against accidental restarting.

The professional must check the electrical characteristics, connection diagram, pinout and connections before putting the new equipment into operation.

The manufacturer's documentation and the requirements applicable to the installation must be respected.

Precautions in a humid environment

The IPX4 rating appearing on the label does not mean that the case can be immersed or directly exposed to a continuous flow of water.

The module must be installed in the location provided by the manufacturer, respecting the electrical protections and the constraints linked to the presence of water.

Avoid any unintended projection on the connections and internal components.

Maintenance and prevention

It It is recommended to periodically check the apparent condition of the cables, accessible connectors and equipment protections, in accordance with the instructions.

Do not open the case and do not attempt to repair the internal electronic circuits without appropriate qualification.

Cleaning of the accessible parts must be carried out without power, using a method compatible with the materials and the manufacturer's recommendations.

Japan Head Spa after-sales service

For a request for identification or compatibility of this electronic box, contact our after-sales service.

After-sales service email: sav.japanheadspa@gmail.com

Also consult our collection of Head Spa control panels and electronic modules.

What is the Head Spa TL-A10-800 control panel used for?

The TL-A10-800 is an electronic box for a compatible Head Spa water circulation system. It can be used to replace a defective original module after checking its compatibility.

What is the exact reference of this panel?

The reference on the technical label is TL-A10-800.

What is the power of the TL-A10-800?

The box has an indicated output power of 800 W.

What electrical voltage is indicated ?

The label reads AC 110 V / 220–240 V. The actual configuration and compatibility with your installation must be confirmed before connection.

What is the frequency indicated on the box?

The frequency listed is 50–60 Hz, under the heading “Output Frequency”.

Which pump is provided in the specifications?

The nameplate indicates a pump specification of 12 V – 25 W. This data must correspond to the electrical circuit concerned on your equipment.

Is the TL-A10-800 compatible with a 24 V pump?

The specified specification is 12 V – 25 W. Compatibility with a 24 V pump without technical confirmation from the manufacturer.

What does the IPX4 index mean?

IPX4 corresponds to protection against splashing water under the conditions defined by the classification. This does not mean that the module is submersible or completely waterproof.

Which standard appears on the label?

The label mentions EN IEC 55014-1:2021, a standard relating to electromagnetic emissions for certain categories of equipment.

Does this enclosure bear a CE marking?

Yes, the CE marking is present on the photographed label. Applicable compliance documents should be consulted separately if necessary.

Can a TL-B10-800 be replaced by a TL-A10-800?

Interchangeability between these two part numbers is not confirmed. You must check the connectors, pinout, electrical characteristics and obtain technical confirmation before replacement.

Is this panel universal for all Head Spas?

No. Compatibility depends on the original reference, electrical characteristics and connector configuration of the equipment.

Why is my Head Spa control panel no longer responding?

The problem can come from the electronic box, but also from the power supply, cables, connectors or other components. A professional diagnosis is recommended before replacement.

Can this box be installed yourself?

Replacement must be carried out by a qualified electrical professional, taking into account the risks associated with the mains supply and electrical connections.

How to check the connections of the TL-A10-800?

It is advisable to compare the number and shape of the connectors, their arrangement, pinout and characteristics of the original module with those of the proposed enclosure.

Where to buy a replacement Head Spa control panel?

Japan Head Spa offers a selection of Head Spa control panels and electronic enclosures for compatible equipment.

What is the price of the TL-A10-800 panel?

The Head Spa TL-A10-800 control panel is priced at €349.00 including tax.

Is delivery free?

Delivery is free from 50 € of purchase, depending on the conditions applicable to the order.

How to contact after-sales service to check compatibility?

Contact our after-sales service at sav.japanheadspa@gmail.com with photographs of the technical label and connectors of your original box.