Installation of a Head Spa table with connection

A Head Spa table isn't installed like a simple piece of furniture. It combines a treatment station, a water supply, drainage, and electrical equipment. If you're looking for a Head Spa table installation and connection, start with the feasibility of the space rather than the aesthetics. To outline the points to check, see our article on the installation of a head spa tub.

The connection ensures smooth operation without manual filling or emptying of the tanks. However, it requires careful preparation before the equipment arrives. The table's position, pipe routing, electrical safety, and maintenance must all be considered together to avoid costly modifications.

Can your premises accommodate a Head Spa table?

Start by measuring the empty room, then imagine the entire flow of a session. The client must be able to enter, lie down, and get up without any obstruction. You must also be able to reach the shower head, controls, towels, and products without having to twist and turn excessively.

A full-length treatment table typically measures around 2.1 meters, depending on the model. Allow sufficient clearance behind the client's head for the practitioner. Lateral clearance also facilitates the patient's entry and exit.

Mark the footprint of the furniture on the floor with masking tape. Add the space needed for the stool, trolley, and door opening. This method quickly reveals narrow passages, obstructing furniture, and inaccessible areas.

The room must also be able to withstand humidity, splashes, and cleaning. Opt for a stable and easy-to-maintain floor. Check the ceiling height if your equipment includes an arch, a fumigation system, or a lighting device.

To compare formats and identify the configuration best suited to your cabin, consult our dedicated page on the table head spaYou can then compare the stated dimensions with the actual measurements of your premises.

What connections need to be made before delivery?

Imagine the installation completed, with the table positioned against a technical wall. Three elements must be available nearby: a cold water supply, a hot water supply, and a wastewater drain.

The water supply must remain accessible to allow for rapid intervention. Install clearly marked shut-off valves. These facilitate maintenance and allow for quick water shut-off in case of a leak.

The drain deserves special attention. Check its diameter, slope, and location relative to the table outlet. A drain that is too far away or poorly positioned can slow the flow and complicate cleaning.

Do not use pipe dimensions from another sink. Consult the instructions for the chosen model before having the work done. When the distance between the sink and the existing plumbing is significant, have a plumber confirm the routing.

A bypass from an existing hairdressing unit can sometimes be feasible. However, it must be checked on site. The pressure, temperature, drainage slope, and access to the fittings must meet the equipment requirements.

To learn more about preparing a project for a salon or spa, we recommend our article dedicated to the installation of a head spa in a salon or institute.

Why should ergonomics guide the layout?

An installation can be technically sound but still remain uncomfortable on a daily basis. practitioner ergonomics It must therefore be checked before the table is permanently fixed.

The practitioner must be able to sit with their feet firmly planted and their shoulders relaxed. Their forearms should remain close to the edge of the basin. The controls, shower head, and towels must be easily accessible without having to bend over for extended periods.

Client comfort also depends on positioning. The neck should rest naturally in the designated cutout. Check the alignment of the pelvis, neck rest, and head before the first treatment.

A publication of Public Health France The report published in 2026 highlights that noise and certain occupational exposures are particularly relevant to electrical and plumbing installation work. While this data pertains to installation trades, it also calls for the creation of safer work sites and treatment areas.

Therefore, avoid placing the table near a hairdryer, a passageway, or a noisy technical room. A quiet booth enhances the perceived quality of the ritual and reduces interruptions during the ceremony.

Connected table or standalone unit, which choice depends on your activity?

The connection is particularly useful if you already have a water source nearby and plan to receive several treatments regularly. You then benefit from a continuous supply, without having to refill the tank or transport wastewater.

THE autonomous block It meets the requirements of a different organization. It includes a clean water tank and a wastewater tank. In the Japan Head Spa range, the mobile units have an integrated tank with a stated capacity of 60 liters.

This configuration is suitable for a multi-purpose cabin, a shared space, or a room where plumbing work is difficult. However, it requires daily water management, including filling, emptying, and cleaning the tanks.

In July 2026, a market research 2026 describes a new cycle for wellness equipment in France, following a stabilization of demand since 2025. This evolution does not determine your installation, but it confirms the importance of choosing equipment consistent with your level of activity.

How to secure the electricity supply and commissioning process?

Water and electricity should be kept separate as much as possible in the layout of the workstation. The power outlet must remain accessible, protected from splashes, and suitable for the power requirements of the model.

Do not place power strips on the floor in a damp area. If you are unsure about the available wiring, consult an electrician before delivery. A preliminary check will prevent the need to modify the installation after the equipment arrives.

In its 2021 data, theInsee distinguishes between electrical installation work water and gas installation work. This distinction highlights that a project may require the validation of several technical skills.

1. Measure the room, passageways, door and traffic area.
2. Locate the water inlets, the drain, and the shut-off valves.
3. Check the electrical outlet, available power, and circuit protection.
4. Observe the fittings during a prolonged test to detect a slow leak.
5. Conduct a trial treatment with a member of your team before opening.

The test must replicate real-world usage conditions. Check the temperature, pressure, jets, shower head, misting system, and drainage. Then check the table's stability and neck support.

Finally, plan a maintenance procedure. It must specify the cleaning of the basin, the shower head, the neck rest, the contact surfaces and the water circuits according to the manufacturer's instructions.

To examine the features of a model and prepare your technical questions, you can consult the datasheet of the Hikari spa table headAlways use the information from the datasheet that corresponds to the actual available reference.

Take action with Japan Head Spa

You've measured your treatment room, but you're still hesitating between a fixed, connected table and a self-contained mobile solution. We can help you tailor your technical setup to your treatment schedule, your available space, and your daily routine.

Our selection includes Head Spa tables with plumbing connections and freestanding units without. Depending on the model, you can also explore features such as steam, water jets, chromotherapy, heating, and filtration. Browse our range of Table head spa with connection to compare the available solutions before validating your installation.